Raptor #1 Radio Configuration
<under construction>

Back to Main Page

 !!!NOTE:  These settings work for me. They
should only be used as a reference for any
other Raptor.
Equipment used: Helicopter -------------------- Raptor TTR4830-A
Raptor 50 conversion kit --------- TT3807
Engine --------------------------------- OS 50 SX-H
Muffler -------------------------------- Gr8Lakes Custom 46
Fuel ------------------------------------ Power Master 15% All synthetic 20% oil
Main Blades ------------------------- SAB Fiberglass 600mm
Tail Blades --------------------------- NHP 85mm
Radio -------------------------- Futaba 8UHFS
Receiver ---------------------- Futaba R148DF
Battery ------------------------ 4.8V 1100mah 'A' cells
Elevator/Aileron Servos -- Hitec 545 (gooped wires)
Collective servo -------------Hitec 545 (gooped wires)
Throttle servo --------------- Hitec 525 (gooped wires)
Tail rotor servo ------------- Futaba 9253
Gyro --------------------------- Futaba GY401
Remote glow plug extender ----- TTR3803
Glow plug ---------------------------- OS #8
Battery monitor/Glitch counter-- BC6
MA carbon tailboom support rods MA #0585-5
T&T Engineering 2oz header tank
Metal collective pitch arm from Ron Lund (Rick's R/C)
Metal increased air flow fan from Ron Lund (Rick's R/C)
Metal washout base from Geoffrey Woodward
QuickUK RC-05 metal swashplate
Wild Chartreuse (bright yellow) SEM 3278
Bright Teal Acme # pb-45877Y manufacture code WA9830 25
Pitch Normal ------------------- -6,+4,+9
Flight mode 1 ----------- -10, 0, +9
Throttle hold ------------ -10, 0, +11
Rod lengths Long links to head (left&right) - 102mm
Short links on head (left&right) - 29mm
Elevator link (back) - 65mm
Elevator link (front) - 83mm
Aileron links to swashplate (left&right) - 54mm
Aileron to servo (left) - 70mm
Aileron to servo (right) - 69mm
Aileron servo arm (center to ball) - 11.5mm
Collective link - 56mm
Collective servo arm (center to ball) - 11.5mm
Throttle link - 73mm
Throttle servo arm (center to ball) - 9mm
Basic Menu
TH-CRV/NORM
1 2 3 4 5
23 40 48 58 85
PI-CRV/NORM
1 2 3 4 5
18 40 60 82 87
REVOLU/NORM
"ON"
1 2 3 4 5
0 0 0 0 0
ATV
AI(1) 87 90
EL(2) 97 84
TH(3) 111 36
RU(4) 80 80
GY(5) 100 100
PI(6) 98 100
(7) 100 100
(8) 100 100
D/R
ch. UP DOWN switch
AI(1) 100 100 SW-D
EL(2) 100 100 SW-A
RU(4) 100 100 SW-B
EXP
ch. UP DOWN
AI(1) 0 0
EL(2) 0 0
RU(4) 0 0
REVERS
AIL NORM
ELE NORM
THR NORM
RUD REV
GYR NORM
PIT REV
CH7 NORM
CH8 NORM
PARA
DATA RSET ATL-ON EG/S-INH HELI1-SWH1 MOD-PPM
INVERT - MODE - INH
TRIM
RSET
AI(1) STEP-4
EL(2) STEP-4
TH(3) STEP-8
RU(4) STEP-1
DISP-NEGA
SUBTRM
AIL +42
ELE 0
THR -120
RUD 0
GYR 0
PIT 0
CH7 0
CH8 0
TRAINR
INH
AIL FUNC
ELE FUNC
THR FUNC
RUD FUNC
GYR OFF
PIT OFF
CH7 OFF
CH8 OFF
TH-CUT
"OFF/ON" -15% 10% SW-H DOWN
MODEL NAME RAP-01
TIMER 08:00DN STK3 3%
Advanced Menu
TH-CRV
NORM 23 41 51 61 85
IDL1 82 72 57 72 82
IDL2 (inh) 100 65 52 65 100
TH-HLD HLDP +35%
RUDDER OFST(inh) 0%
OFST-1
AIL -38
ELE -21
RUD 0

SW-E
OFST-2 (inh)
AIL 0
ELE 0
RUD 0
OFST-iv (inh)
AIL 0
ELE 0
RUD 0
DELAY
AIL 0
ELE 0
RUD 0
PMIX-1
AIL-> THR
+25% -25%
LINK OFF
TRIM OFF
OFST 0%
SW-E C/DN
PMIX-2
ELE-> THR
+26% -26%
LINK OFF
TRIM OFF
OFST 0%
SW-E C/DN
HOV-TH (inh)
0% 0%
HOV-PI (inh)
0% 0%
GYRO
NORM 90%
IDL1 90%
IDL2 10%
SW-E  
GOVrpm (inh)
UP 0%
CNTR 50%
DOWN 100%
HOLD CH7
HOLD lmt+
SW-C  
TH-NDL (inh)
IDLE
1 2 3 4 5
0 25 50 75 100

ACCE 0%
TH-NDL (inh)
NORM
1 2 3 4 5
0 25 50 75 100

ACCE 0%
INVERT (inh) CRSS 30%
REVOLU - IDL2
1 2 3 4 5
0 0 0 0 0
REVOLU - IDL1
1 2 3 4 5
0 0 0 0 0
REVOLU - NORM
1 2 3 4 5
0 0 0 0 0
PI-CRV
NORM 18 40 60 82 87
IDL1 0 25 50 74 95
IDL2 0 25 50 62 88
HOLD 10 40 50 75 100
INVR 0 25 50 75 100
TH-CRV
NORM 23 41 51 61 85
IDL1 82 72 57 72 82
IDL2 (inh) 100 65 52 65 100