T-Rex 600N Sport
Bought at IRCHA 2007 8-11-2007 by Mike Rice as a gift to me.

Installed three Hitec 6975, DS821(throttle) engine (TT50). muffler Hatori SB-15FH) Spektrum AR7000 receiver, Futaba GY401/9254 JR Heavy Duty Switch, V-Blade 600mm  

8-18 3 tanks (auto hub Sticking)  
8-19 2 tanks (auto hub Sticking)
8-21 1 tank Auto hub broke The plastic container for the needle bearings is cracked 
8-24 Installed new auto hub 
8-24 1 tank
8-24 Installed GV-I magnets 
8-25 1/3 tank RevMaX not working suspect magnets gone again. 
8-25 2/3 tank
8-26 installed one GV-1 magnet and set screw
8-26 1 tank (threw magnet again) 
8-27 1 tank
8-28 1 tank
8-29 installed Optical sensor 
9-1 3 tanks 
9-2 4 tanks 
9-3 partial tank 
9-8 3 tanks 
9-9 2 of 3 tanks 
Installed weights on flybar 
9-9 1 of 3 tanks 
9-12 2 tanks 
9-15 2 tanks 
9-16 5 tanks {lost radio at end of 5th tank, battery was good) 
9-20 2 of 3 tanks 
Installed long flybar 
9-20 0.5 of 3 tanks 
Installed Curtis Stuby paddles. 
9-20 0.5 of 3 tanks 
Installed stock paddles 
9-23 2 tanks
9-25 2 tanks
<40 tanks> 
9-29 Removed canopy, tail boom support rods, and vertical fin. 
9-29 to 9-30 painted canopy, tail 3 boom support rods, 2 tail booms. Raptor horiz fin, and vertical fin. 
10-1 Installed painted parts. 
10-2 1/4 tank 
10-5 installed V-Paddles 
10-5 1 tank
10-7 3 tanks 
10-9 3 tanks 
10-10 2 tanks 
<49 tanks> 
10-11 2 tanks 
10-12 2 tanks 
10-13 7 tanks 
10-14 5 tanks 
10-14 installed screws through side of skids to hold them in. 
10-16 3 tanks 
10-17 replaced split O-rings in muffler  
10-18 3 tanks (running great!) 
10-19 2 tanks
10-21 10 of 11 tanks
1000th flight on my V-Blades 
10-21 1 of 11 tanks
<84 tanks> 
10-26 3 tanks 
10-27 3 of 7 tanks 
tighten screws on seesaw mixing arms and rear tail lever. 
Installed kB tail blades 
10-27 4 of 7 tanks 
10-28 1 of 2 tanks 
Replaced dampers
10-28 1 of 2 tanks 
Clutch broke. Replaced both link ends on the throttle rod. Replaced ball on carburetor lever. 
10-30 Installed new clutch 
10-30 1 tank 
10-31 took clutch out and ground outside of hub half way around because clutch had 0.004"  Now runout is 0.0015"
Gap is 0.005'' per side. Instead of the previous 0.008". 
10-31 2 tanks 
<99 tanks> 
11-1 1 tank
11-2 2 tanks 
11-3 3 tanks 
11-4 1 tank