T-Rex 600N Sport
Bought at IRCHA 2007 8-11-2007

Installed three Hitec 6975, DS821(throttle) engine (TT50). muffler Hatori SB-15FH) Spektrum AR7000 receiver, Futaba GY401/9253 JR Heavy Duty Switch, V-Blade 600mm  

8-18 3 tanks (auto hub Sticking)  
8-19 2 tanks (auto hub Sticking)
8-21 1 tank Auto hub broke The plastic container for the needle bearings is cracked 
8-24 Installed new auto hub 
8-24 1 tank
8-24 Installed GV-I magnets 
8-25 1/3 tank RevMaX not working suspect magnets gone again. 
8-25 2/3 tank
8-26 installed one GV-1 magnet and set screw
8-26 1 tank (threw magnet again) 
8-27 1 tank
8-28 1 tank
8-29 installed Optical sensor 
9-1 3 tanks 
9-2 4 tanks 
9-3 partial tank 
9-8 3 tanks 
9-9 2 of 3 tanks 
Installed weights on flybar 
9-9 1 of 3 tanks 
9-12 2 tanks 
9-15 2 tanks 
9-16 5 tanks {lost radio at end of 5th tank, battery was good) 
9-20 2 of 3 tanks 
Installed long flybar 
9-20 0.5 of 3 tanks 
Installed Curtis Stuby paddles. 
9-20 0.5 of 3 tanks 
Installed stock paddles 
9-23 2 tanks
9-25 2 tanks
<40 tanks> 
9-29 Removed canopy, tail boom support rods, and vertical fin. 
9-29 to 9-30 painted canopy, tail 3 boom support rods, 2 tail booms. Raptor horiz fin, and vertical fin. 
10-1 Installed painted parts. 
10-2 1/4 tank 
10-5 installed V-Paddles 
10-5 1 tank
10-7 3 tanks 
10-9 3 tanks 
10-10 2 tanks 
<49 tanks> 
10-11 2 tanks 
10-12 2 tanks 
10-13 7 tanks 
10-14 5 tanks 
10-14 installed screws through side of skids to hold them in. 
10-16 3 tanks 
10-17 replaced split O-rings in muffler  
10-18 3 tanks (running great!) 
10-19 2 tanks
10-21 10 of 11 tanks
1000th flight on my V-Blades 
10-21 1 of 11 tanks
<84 tanks> 
10-26 3 tanks 
10-27 3 of 7 tanks 
tighten screws on seesaw mixing arms and rear tail lever. 
Installed kB tail blades 
10-27 4 of 7 tanks 
10-28 1 of 2 tanks 
Replaced dampers
10-28 1 of 2 tanks 
Clutch broke. Replaced both link ends on the throttle rod. Replaced ball on carburetor lever. 
10-30 Installed new clutch 
10-30 1 tank 
10-31 took clutch out and ground outside of hub half way around because clutch had 0.004"  Now runout is 0.0015"
Gap is 0.005'' per side. Instead of the previous 0.008". 
10-31 2 tanks 
<99 tanks> 
11-1 1 tank
11-2 2 tanks 
11-3 3 tanks 
11-4 1 tank
11-10 2 tanks 
11-11 4 tanks 
11-17 3 of 5 tanks 
Had a really hard bounce in a near crash circumstance and put two small cracks in right frame plate just above rear strut. Used clear Gorilla glue. 
11-17 2 of 5 tanks 
<117 tanks> 
11-18 1 of 6 tanks
Replaced ball on tail pitch slider. 
11-18 5 of 6 tanks 
12-1 5 tanks 
12-2 1 tank 
12-8 3 tanks 
12-16 2 tanks
12-23 3 tanks
12-29 3 tanks
12-30 3 tanks
1-5-2008 2 tanks 
1-12 4 tanks
1-20 1 tank 
1-26 1 tank 
1-27 3 tanks
2-2 6 tanks
<160 tanks> 
2-3 3 tanks
2-9 4 tanks 
2-10 7 tanks
2-13 Replaced hatori exhaust deflector 
2-13 added frame brace set HN6069T and replaced dampers with all black from kit HN6061T sleeve set Installed sleeve. 
2-16 1 tank 
2-17 1 tank 
2-23 1 tank
Replaced tailboom due to wear at horizontal fin clamp. 
2-24 3 tanks  
3-1 1 tank
3-2 1 tank
3-8 1 of 3 tanks
<183 tanks> 
Removed tt50 engine (had 513 tanks) 
Installed TT Redline engine 
Replaced ball and link on throttle servo arm. 
3-8 2 of 3 tanks. Runs great! Main needle is 2-1/4 and mid is flush with carb. body. 
3-9 9 tanks
3-11 1 tank 
3-12 installed metal horiz. Fin clamp.
3-12 2 tanks 
3-15 2 tanks 
3-16 3 tanks 
3-16 Replaced ball and link at front of rear tail control rod. 
3-20 3 tanks 
3-21 2 tanks
<207 tanks> 
3-22 3 tanks 
3-23 3 tanks 
3-24 1 tank
3-25 Replaced prism tape on blades.
3-27 1 tank
3-29 1 tank
4-5 replaced clunk line
4-5 6 tanks 
4-6 Replaced ball-anti-rotation rod on front of swashplate. Rod was worn. Replaced one thrust bearing.  
4-6 5 tanks 
4-7 3 tanks 
4-10 1 tank 
<231 tanks> 
4-11 3 tanks
4-12 2 of 3 tanks
4-12 Replaced canopy grommet on right side with Raptor grommet 
4-12 1 of 3 tanks
Replaced exhaust deflector.  
4-14 2 tanks
4-16 1 tank 
4-19 1 tank 
4-20 2 tanks
4-21 3 tanks 
4-22 3 tanks 
4-26 Replaced gyro tape and ball & link at back of rear tail control rod.
4-28 3 tanks 
4-29 4 tanks 
<256 tanks> 
5-1 Replaced both links on front tail rod and ball at back. 
5-1 1 tank 
5-4 4 tanks 
5-5 1 tank 
5-6 1 tank 
5-8 4 tanks
5-9 1 tank 
5-10 2 tanks
5-12 1 tank 
5-16 2 tanks 
5-16 Replaced glow plug OS #8 
5-17 5 tanks
5-18 4 tanks
5-19 1 tank
5-20 1 tank
<284 tanks> 
5-21 1 tank
S-22 4 tanks
5-24 2 tanks
5-25 7 tanks 
5-26 Replaced the four balls at the top and bottom of the long links. 
5-26 2 tanks
5-29 2 tanks
6-2 1.65 tanks Crash due to bad clunk line. Just as I flipped upside down the engine died. Got it upright but landed hard and broke landing gear. 
6-3 Replaced landing gear and clunk line 
6-3 1 tank
<304 tanks> 
6-7 1 tank
6-28 1 tank
6-29 1 tank
7-1 0.3 tank 
7-1 installed new V-Blades TST Extreme 600mm 
7-5 4 tanks 
7-6 1 tank 
7-7 1 tank (at Jerry's House showing Scotty Philips)
7-11 2 tanks (at Kevin's workplace) 
7-13 1 tank (at HS track)  
7-19 2 tanks 
7-20 1 tank 
7-26 1 tank 
7-27 4 tanks 
7-27 crashed on beginning of 5th tank Did a hard rainbow and On the inverted side the heli crashed in the air.  V-Blades ruined, tail boom,   flybar, one skid, and two double links gone. 
8-4 installed My old V-Blades that I was using and checked main and Spindle shafts. 
8-5 installed my old oroginal flybar (400mm)  Made up two new double links. 
8-5 1 tank 
8-6 5 tanks 
8-9 Replaced glow plug with OS #8 
8-9 1 tank 
8-23 1 tank
8-23 Replaced o-rings in Muffler and two rubber grommets. Replaced missing bolts. Replaced pressure line. Reglued the optical sensor for the RevMax. 
8-24 5 tanks
8-25 2 tanks  
<339 tanks> 
8-30 4 tanks  Suspect engine bearing is failing. 
8-31 Rear bearing was bad. Installed new bearing. Replaced ball and link at bottom of throttle rod. 
8-31 2 tanks
9-1 1 tank 
9-6 3 of 8 tanks 
Replaced gyro tape 
9-6 5 of 8 tanks 
9-7 7 tanks 
9-15 2 tanks 
9-16 2 tanks 
9-17 2 tanks 
9-21 1 of 5 tanks
Replaced clunk line  
9-21 4 of 5 tanks 
9-23 3 tanks 
9-24 1 tank 
Main tail gear is worn bad
10-1 Replaced tail gear and the front tail belt gear. Also replaced belt. 
10-1 1 tank
10-2 3 tanks
10-4 1 tank
10-4 installed A123 battery pack and 5.6v regulator 
10-5 1.5 tanks 
Heard Vibration and landed. Found blade grip split at blade Bolt. 
<382 tanks> 
12-31 Removed the three Hitec 6975 to put in Raptor #5